Radiant heat travels through air, and typically heats up objects closer to the panel first and then the rest of the room later. Infrared heating from the panel can be easily detected from about 3-4 feet. Ideally, the radiant panel should be aimed onto the area with more use, since that will be the surface that will warm up first.
Sunrooms can be very cold during the winter months. While a furnace may push some warm air into the room, the large number of windows, exterior walls, and other causes of heat loss in a sunroom will typically keep it from having a comfortable temperature level. Floor heating and radiant panels will add radiant heat, which the human body absorbs faster than other forms of heat, to the room so that it feels warm even at lower temperatures.
Radiant heat travels through air, and typically heats up objects closer to the panel first and then the rest of the room later. Infrared heating from the panel can be easily detected from about 3-4 feet. Ideally, the radiant panel should be aimed onto the area with more use, since that will be the surface that will warm up first.
We do not have a Radiant Panels Running Cost Calculator. However, this can be determined easily by taking the panelâs wattage, dividing it by 1000, and then multiplying the result by the local kW/hr cost â then take this hourly cost and multiple by 730 hours to get a monthly estimate.
Verify that the mounting bolts are fully tightened on the rail. If not, tighten them until snug. If bolts are tight, look behind the LAVA and check to see if the rail is touching the rear of the enclosure.  If it isâthat is the cause of the sound. Solution: Take some felt, and attach it in between the rail and enclosure.
We recommend a 1.4" (3.6cm) joint/space perimeter around the glass for air circulation and easier installation. Furthermore, no flammable materials may be used around the LAVA. It's required by UL that the âOn/Offâ switch must be operable and visible. Please check with your local electrical code prior to installing your Lava panel for restrictions on placement.
Floor heating will typically add the most heat to supplement an existing heating source and it will not take any extra space since it is embedded in the floor. If you are not remodeling your floors but have some open wall space, you should mount a radiant panel. For the most effective results, install the panel so that it points toward the area where you will spend most of the time.
Radiant panels can be installed in bathroom if they are far enough away from water sources. These units are not allowed in any shower or tub enclosure. Make sure that the infrared heating system cannot be touched by any person who is in the bath or shower. Please install in accordance with local electrical code requirements.
The startup heating time for this infrared heating system is approximately 5 to 10 minutes. However, your room will not feel warmer immediately because the cold objects in the room (furniture, walls, ceilings, floors, etc.) need to warm up first. Once these surfaces are heated via infrared heating, the warmth will spread throughout the room.
Yes, sunrooms can be used in the winter, just activate your floor heating or radiant panel and turn your sunroom into a 4-season room. You will notice a tremendous difference in the room comfort, especially with the thermostat set to maintain a desired ambient temperature. WarmlyYours thermostats will do the work for you by energizing the floor for longer cycles.
Verify 120V power at the connection to the panel at the junction box at the rear of the panel. Verify the panel power switch is in the "ON" position (if equipped). LAVA internal temperature limiters may have actuated. Turn off the unit using the "Power" switch on the panel and wait 30-60 minutes for the unit to reset. Turn the unit back on and operate normally.
If you experience additional issues, please give us a call at 1-800-875-5285.
A LAVA panel cannot be installed in "wet locations" such as showers or saunas. The top, bottom, and sides of the unit must not be closer than 12 inches from any other object or surface in order to effectively radiate heat. The LAVA panels may not be placed behind doors. Please check with your local electrical code prior to installing your LAVA panel for restrictions on placement.
You can connect your plug-in radiant panels to a line voltage automated or a manual switch, timer, plug-in thermostat, or wifi switch. You can also use one of the controls found on our web page; https://www.warmlyyours.com/en-US/radiant-panels/controls
Please abide by local electrical code guidelines. Lava radiant panels may not be installed in "wet locations" such as showers or saunas. The top, bottom, and sides must not be closer than 12 inches from any other object or surface in order to effectively radiate heat. The Lava radiant panels may not be placed behind doors. We do not recommend installing Lava radiant panels on ceilings.